怎样安装NVIDIA显卡驱动程序？

mtx

在SUSE下安装显卡驱动比较麻烦，怎样安装，请指教！

Ouranos

与其他发行版安装相同，先安装GCC和内核源码包。然后在安装驱动

mking007

从Yast安装，不用安装内核源码就可以。这是Nvidia和SuSE推荐的方法。

guangguang

Nvidia的驱动做得很好啊，根据readme安装就ok了，我都装了好几次了

wise

nvidia主页上写的本地安装方法如下：
People who aren't afraid of recompiling the nvidia kernel module or
even reinstalling the nvidia driver each time the kernel has been
updated and want or need to use the latest and greatest nvidia driver
can use the following steps 1-3. The others should use the
instructions above using YOU and skip the steps below.

1) Kernel sources must be installed and configured. Usually this means
installing the 'kernel-source', 'make' and 'gcc' packages with YaST2.
Update it - if not already done - via YaST2 Online Update (YOU).

2) Use the nvidia installer for 1.0-7676.

sh NVIDIA-Linux-x86-1.0-7676-pkg1.run -q

3) Configure X.Org with

sax2 -m 0=nvidia (0 is a digit, not a letter!)

NOTE: There is no need to try to enable 3D support. It's already
      enabled, when the nvidia driver is running.

这个三步里面的第一步是什么意思，能不能翻译一下，我第一次用linux，不知道怎么操作，刚在nvidia主页上载了一个NVIDIA-Linux-x86-1.0-7676-pkg1.run，然后不知道怎么安装。
第二第三步我大概能看懂，反正好像是输入命令就可以了吧，第一步就不清楚了……请大家指点一下。

Ouranos

第一步就是你的系统中需要有kernel-source，gcc和make

whb

下载新的nv驱动，在文本方式下进入nv驱动所在的目录，输入：sh NVIDIA-Linux-1.0-7174-pkg1.run     会提示找不到kernel interface , 也不用重新下载安装，而是继续，自然会装好( 其他版的驱动可能失败，我也试过不行，但这个1.0-7174绝对能行，因为我已经实践并成功安装了)
最后启用新的驱动，输入:  sax2  -m  0=nvidia
它会自动修改/etc/X11/xorg.conf 文件的，把nv改为nvidia

real_me

Post by wise
nvidia主页上写的本地安装方法如下：
1) Kernel sources must be installed and configured. Usually this means
installing the 'kernel-source', 'make' and 'gcc' packages with YaST2.
Update it - if not already done - via YaST2 Online Update (YOU).

2) Use the nvidia installer for 1.0-7676.

sh NVIDIA-Linux-x86-1.0-7676-pkg1.run -q

3) Configure X.Org with

sax2 -m 0=nvidia (0 is a digit, not a letter!)

NOTE: There is no need to try to enable 3D support. It's already
      enabled, when the nvidia driver is running.

我就是照他说的安装，可是装完没几天就画屏，X进不去，卸载了就好了

chases

init 3
sh *****.run --add-this-kernel
sh *****-custom.run
改xorg.conf里的nv为nvidia

我的是6200A显卡，用Yast装好就花屏。用以上方法成功。

zun

我用YaST装nvidia后设置3D－Enable后，重启后花屏，不知道哪位帮忙指点一下该怎样设置。