Conexant USB ADSL驱动的解决办法

flyingpot

不知道那位老大在mandrakelinux10中使用UsbADSL上网成功？分享一下经验吧？？！！！

budaodao

现在拔号完了可以看到一个设备nas0。可是没见到给他分配的IP
这是为什么？



root@0[ppp]# cxstart.sh
>>> Inits Conexant AccessRunner <<<

>>> Loading firmware...
Conexant AccessRunner microcode upload program. 6/9/2003
Josep Comas <jcomas@gna.es>
See credits in documentation

I found ADSL modem with VendorID = 0572 & ProductID = cb00
Loading and sending /usr/sbin/cxfirm4.bin...
Firmware is sent!
Setting configuration...
Waiting ADSL line is up (until 90 seconds)...
........
ADSL line is up (Downstream 576 Kbits/s, Upstream 128 Kbits/s)
>>> Loading driver...
Launching driver in normal mode...

/usr/sbin/cxload.sh successful
Setting PPP over Ethernet...
>>> Setting PPPoE <<<

>>> Loading br2684 kernel module...

>>> Loading ppp_generic...

>>> Loading br2684ctl...
Conexant AccessRunner ioctl call. 6/9/2003
Josep Comas <jcomas@gna.es>
See credits in documentation

I found ADSL modem with VendorID = 0572 & ProductID = cb00
br2684ctl[8494]: Interface "nas0" created sucessfully
br2684ctl[8494]: Communicating over ATM 0.8.35, encapsulation: LLC
br2684ctl[8494]: Interface configured

>>> Activating interface...
>>> Activating send/receive data...

>>> Loading pppd daemon...
Plugin /usr/lib/pppd/2.4.2/pppoatm.so loaded.
PPPoATM plugin_init
PPPoATM setdevname - remove unwanted options
PPPoATM setdevname_pppoatm - SUCCESS:8.35
/usr/sbin/pppd: In file /etc/ppp/peers/dsl-provider: unrecognized option 'pty'
root@0[ppp]# ifconfig
lo Link encapocal Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:174 errors:0 dropped:0 overruns:0 frame:0
TX packets:174 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:11630 (11.3 KiB) TX bytes:11630 (11.3 KiB)

nas0 Link encap:Ethernet HWaddr 00:00:01:00:00:00
inet6 addr: fe80::200:1ff:fe00:0/64 Scopeink
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:428 (428.0 b)

lianyunqing

问一下这些参数
VPI=0  VCI=33

PPP over Ethernet llcsnad(RCF2516)

Idle G.dmt
在win下怎么看呀

hyzjh336

我的设备与你的一样，我现在就在linux给你回，我是这样做的，
1、在window 98下连线，在dos模式下，用ipconfig /all 查DNS
2、adsl-setup
设备nas0
按要求填用户名等
DNS 填window下查到的
3、cxstart.sh试一下

saintw

我是纯的新手
大家帮我看看怎么才能让我的 modem 工作
系统环境 fc3
具体看我的签名
modem vendor ID = 0572 & Product ID = cb00

费了好大劲可算让 cxstart.sh 没什么错误了


结果还是上不了网

希望我表达的够明白

图片一

图片二

zdchl

我按照你们的安装方法在9.0上安装实达的5800usb adsl modem的驱动中
使用cc -o br2684ctl brct2684.c -latm时，
提示如下错误
ATM_BACKEND_BR2684 undeclared
ATM_NEWBACKENDIF     undeclared

请问，我该怎么办？