LinuxSir.cn,穿越时空的Linuxsir!

 找回密码
 注册
搜索
热搜: shell linux mysql
查看: 530|回复: 1

CDMA上网求助

[复制链接]
发表于 2006-10-29 12:40:37 | 显示全部楼层 |阅读模式
我用的是ubuntu6.06,查了不少资料,以为终于可以用PCMCIA-CDMA上网了,可是最后一步还是不行,这是在我的机器上得到的信息,我用的是PCMCIA的上网卡,各位帮帮忙
1、cat /proc/bus/usb/devices

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  '''Vendor=0df7 ProdID=0620 Rev= 0.10'''
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=pl2303
E:  Ad=81(I) Atr=03(Int.) MxPS=  10 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms

2、dmesg |grep usb
[4294684.498000] usbcore: registered new driver usbfs
[4294684.498000] usbcore: registered new driver hub
[4294684.811000] usb 1-2: new low speed USB device using uhci_hcd and
address 2
[4294685.172000] usb 2-1: new full speed USB device using uhci_hcd and
address 2
[4294685.296000] usbcore: registered new driver hiddev
[4294685.502000] usb 3-1: new full speed USB device using uhci_hcd and
address 2
[4294685.661000] input: USB HID v1.00 Mouse [PS/2+USB Mouse] on
usb-0000:00:1d.0-2
[4294685.661000] usbcore: registered new driver usbhid
[4294685.661000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[4294685.681000] usb-storage: device found at 2
[4294685.681000] usb-storage: waiting for device to settle before scanning
[4294685.681000] usbcore: registered new driver usb-storage
[4294690.683000] usb-storage: device scan complete
[4294703.044000] usbcore: registered new driver usbserial
[4294703.045000] drivers/usb/serial/usb-serial.c: USB Serial support
registered for generic
'''[4294703.046000] usbcore: registered new driver usbserial_generic
[4294703.046000] drivers/usb/serial/usb-serial.c: USB Serial Driver core
[4294703.107000] drivers/usb/serial/usb-serial.c: USB Serial support
registered for pl2303
[4294703.108000] usb 2-1: pl2303 converter now attached to ttyUSB0
[4294703.108000] usbcore: registered new driver pl2303
[4294703.108000] drivers/usb/serial/pl2303.c: Prolific PL2303 USB to
serial adaptor driver'''

3、wvdial.conf

[modem0]
Modem = /dev/ttyUSB0
  Baud = 115200
  SetVolume = 0
  Dial Command = ATDT
  Init1 = ATZ
  FlowControl = Hardware (CRTSCTS)
[Dialer cdma]
Phone = #777
  Username = CARD
  Password = CARD
  Stupid Mode = 1
  Inherits = Modem0

4、wvdial cdma
--> WvDial: Internet dialer version 1.55
--> '''Cannot get information for serial port.'''
--> Initializing modem.
--> Sending: ATZ
--> Sending: ATQ0
 楼主| 发表于 2006-10-29 14:50:12 | 显示全部楼层
补充wvdialconf的信息


wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

ttyS0<Info>: Device or resource busy
Modem Port Scan<*1>: S0   S1   S2   S3
ttyS4<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS4<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS4<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S5   S6   S7   S8
Modem Port Scan<*1>: S9   S10  S11  S12  S13  S14  S15  S16
Modem Port Scan<*1>: S17  S18  S19  S20  S21  S22  S23  S24
Modem Port Scan<*1>: S25  S26  S27  S28  S29  S30  S31  S32
Modem Port Scan<*1>: S33  S34  S35  S36  S37  S38  S39  S40
Modem Port Scan<*1>: S41  S42  S43  S44  S45  S46  S47
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 --
ttyUSB0<*1>: failed with 2400 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.


Sorry, no modem was detected!  Is it in use by another program?
Did you configure it properly with setserial?

Please read the FAQ at http://open.nit.ca/wiki/?WvDial
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 注册

本版积分规则

快速回复 返回顶部 返回列表