|
|
楼主 |
发表于 2007-10-30 20:16:20
|
显示全部楼层
dmesg 可以看什么呢，我不知该看什么，看不出来啊
内容如下Linux version 2.6.22-suspend2-r2-gbliu (root@localhost) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #1 SMP Sat Oct 27 06:38:15 CST 2007
Command line: root=/dev/sda11 resume2=swap:/dev/sda9 splash=silent,fadein,theme:emergence console=tty1
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000057e70000 (usable)
BIOS-e820: 0000000057e70000 - 0000000057e80000 (ACPI data)
BIOS-e820: 0000000057e80000 - 0000000057f00000 (ACPI NVS)
BIOS-e820: 0000000057f00000 - 0000000060000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 360048) 1 entries of 3200 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F8500, 0014 (r0 PTLTD )
ACPI: RSDT 57E796EF, 0038 (r1 DELL M08 6040000 LTP 0)
ACPI: FACP 57E7FD06, 0074 (r1 ATI Bowfin 6040000 ATI F4240)
ACPI: DSDT 57E79727, 65DF (r1 ATI SB600 6040000 MSFT 3000000)
ACPI: FACS 57E90FC0, 0040
ACPI: TCPA 57E7FD7A, 0032 (r2 AMD 6040000 PTEC 0)
ACPI: SSDT 57E7FDAC, 01C4 (r1 PTLTD POWERNOW 6040000 LTP 1)
ACPI: APIC 57E7FF70, 0054 (r1 PTLTD APIC 6040000 LTP 0)
ACPI: MCFG 57E7FFC4, 003C (r1 PTLTD MCFG 6040000 LTP 0)
Scanning NUMA topology in Northbridge 24
No NUMA configuration found
Faking a node at 0000000000000000-0000000057e70000
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 360048) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-0000000057e70000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
early_node_map[2] active PFN ranges
0: 0 -> 157
0: 256 -> 360048
On node 0 totalpages: 359949
DMA zone: 56 pages used for memmap
DMA zone: 1822 pages reserved
DMA zone: 2119 pages, LIFO batch:0
DMA32 zone: 4866 pages used for memmap
DMA32 zone: 351086 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000
swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000ce000
swsusp: Registered nosave memory region: 00000000000ce000 - 0000000000100000
Allocating PCI resources starting at 68000000 (gap: 60000000:80000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 33648 bytes of per cpu data
Built 1 zonelists. Total pages: 353205
Kernel command line: root=/dev/sda11 resume2=swap:/dev/sda9 splash=silent,fadein,theme:emergence console=tty1
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 1695.822 MHz processor.
Console: colour VGA+ 80x25
Checking aperture...
CPU 0: aperture @ 3e0000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 1412376k/1440192k available (3895k kernel code, 27420k reserved, 2166k data, 340k init)
Calibrating delay using timer specific routine.. 3394.75 BogoMIPS (lpj=6789503)
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
..MP-BIOS bug: 8254 timer not connected to IO-APIC
Using local APIC timer interrupts.
result 12469291
Detected 12.469 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3391.85 BogoMIPS (lpj=6783707)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual-Core Processor TK-53 stepping 01
Brought up 2 CPUs
migration_cost=186
Device driver platform lacks bus and class support for being resumed.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - e09fffff
PCI: No mmconfig possible on device 00:18
ACPI: System BIOS is requesting _OSI(Linux)
ACPI: Please test with "acpi_osi=!Linux"
Please send dmidecode to linux-acpi@vger.kernel.org
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Device driver pci0000:00 lacks bus and class support for being resumed.
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
Device driver pnp0 lacks bus and class support for being resumed.
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
USB driver usbfs lacks resume support.
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0
pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved
pnp: 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:08: ioport range 0x1080-0x1080 has been reserved
pnp: 00:08: ioport range 0x220-0x22f has been reserved
pnp: 00:09: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:09: iomem range 0xc0004800-0xc0004bff has been reserved
pnp: 00:09: iomem range 0xfed00000-0xfed003ff has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: c0100000-c01fffff
PREFETCH window: c8000000-cfffffff
PCI: Bridge: 0000:00:05.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
IO window: disabled.
MEM window: c0200000-c02fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:14.4
IO window: disabled.
MEM window: c0300000-c03fffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:05.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
NET: Registered protocol family 2
Time: acpi_pm clocksource has been installed.
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 6291456 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.28 [Flags: R/W].
fuse init (API version 7.8)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: MSI quirk detected. MSI deactivated.
Boot video device is 0000:01:05.0
PCI: Setting latency timer of device 0000:00:05.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
Allocate Port Service[0000:00:05.0:pcie02]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie02]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102 (c) Dave Jones
vga16fb: initializing
vga16fb: mapped to 0xffff8100000a0000
fb0: VGA16 VGA frame buffer device
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input2
ACPI: Sleep Button (CM) [SLPB]
input: Lid Switch as /class/input/input3
ACPI: Lid Switch [LID]
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (51 C)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
Device driver lo lacks bus and class support for being resumed.
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 21 (level, low) -> IRQ 21
Device driver eth0 lacks bus and class support for being resumed.
eth0: Broadcom 4400 10/100BaseT Ethernet 00:19:b9:7a:be:7a
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SB600_PATA: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
SB600_PATA: chipset revision 0
SB600_PATA: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8420-0x8427, BIOS settings: hda MA, hdb:pio
Probing IDE interface ide0...
hda: PIONEER DVD+/-RW DR-K17Y, ATAPI CD/DVD-ROM drive
Device driver ide0 lacks bus and class support for being resumed.
hda: selected mode 0x42
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
PCI driver AMD_IDE lacks driver specific resume support.
PCI driver ATIIXP_IDE lacks driver specific resume support.
PCI driver Promise_IDE lacks driver specific resume support.
PCI driver PIIX_IDE lacks driver specific resume support.
Probing IDE interface ide1...
hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
PCI driver aic79xx lacks driver specific resume support.
ahci 0000:00:12.0: version 2.2
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 22
ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:12.0: flags: ncq ilck led clo pmp pio
scsi0 : ahci
Device driver host0 lacks bus and class support for being resumed.
scsi1 : ahci
Device driver host1 lacks bus and class support for being resumed.
scsi2 : ahci
Device driver host2 lacks bus and class support for being resumed.
scsi3 : ahci
Device driver host3 lacks bus and class support for being resumed.
ata1: SATA max UDMA/133 cmd 0xffffc20000330100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
ata2: SATA max UDMA/133 cmd 0xffffc20000330180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
ata3: SATA max UDMA/133 cmd 0xffffc20000330200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
ata4: SATA max UDMA/133 cmd 0xffffc20000330280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: SAMSUNG HM160JI, AD100-12, max UDMA/100
ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
Device driver target0:0:0 lacks bus and class support for being resumed.
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HM160JI AD10 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
PCI driver sata_svw lacks driver specific resume support.
Fusion MPT base driver 3.04.04
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.04
ieee1394: raw1394: /dev/raw1394 device initialized
ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.5: EHCI Host Controller
ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 19, io mem 0xc0004400
ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
Device driver usbdev1.1_ep00 lacks bus and class support for being resumed.
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
Device driver usbdev1.1_ep81 lacks bus and class support for being resumed.
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 16, io mem 0xc0005000
Device driver usbdev2.1_ep00 lacks bus and class support for being resumed.
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Device driver usbdev2.1_ep81 lacks bus and class support for being resumed.
ACPI: PCI Interrupt 0000:00:13.1 -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 17, io mem 0xc0006000
Device driver usbdev3.1_ep00 lacks bus and class support for being resumed.
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Device driver usbdev3.1_ep81 lacks bus and class support for being resumed.
ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.2: irq 18, io mem 0xc0007000
Device driver usbdev4.1_ep00 lacks bus and class support for being resumed.
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Device driver usbdev4.1_ep81 lacks bus and class support for being resumed.
ACPI: PCI Interrupt 0000:00:13.3 -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.3: irq 17, io mem 0xc0008000
Device driver usbdev5.1_ep00 lacks bus and class support for being resumed.
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
Device driver usbdev5.1_ep81 lacks bus and class support for being resumed.
ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.4: irq 18, io mem 0xc0009000
Device driver usbdev6.1_ep00 lacks bus and class support for being resumed.
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
Device driver usbdev6.1_ep81 lacks bus and class support for being resumed.
USB Universal Host Controller Interface driver v3.0
usb 5-1: new low speed USB device using ohci_hcd and address 2
Device driver usbdev5.2_ep00 lacks bus and class support for being resumed.
usb 5-1: configuration #1 chosen from 1 choice
Device driver usbdev5.2_ep81 lacks bus and class support for being resumed.
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input4
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
input: USB Optical Mouse as /class/input/input5
input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:13.3-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
oprofile: using NMI interrupt.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
Device driver sit0 lacks bus and class support for being resumed.
NET: Registered protocol family 17
powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual-Core Processor TK-53 processors (version 2.00.00)
powernow-k8: 0 : fid 0x9 (1700 MHz), vid 0x13
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x14
powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x1a
Suspend v2.2.10
Suspend2 Userspace Storage Manager support registered.
Suspend2 Basic User Interface support registered.
Suspend2 Compressor support registered.
Suspend2 Block I/O support registered.
Suspend2 Swap Allocator support registered.
Suspend2 File Allocator support registered.
Suspend2 Userspace UI support registered.
Synaptics Touchpad, model: 1, fw: 6.3, id: 0x180b1, caps: 0xa04713/0x200000
input: SynPS/2 Synaptics TouchPad as /class/input/input6
Replacing swsusp.
No storage allocator is currently active. Rechecking whether we can use one.
Suspend2: SwapAllocator: Signature found.
Suspend2: Resuming enabled.
Suspend2: Normal swapspace found.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 340k freed
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 1281 MBytes.
[fglrx] ASYNCIO init succeed!
[fglrx] PAT is enabled successfully!
[fglrx] module loaded - fglrx 8.42.3 [Oct 19 2007] on minor 0
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
EXT3 FS on sda11, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ReiserFS: sda8: found reiserfs format "3.6" with standard journal
ReiserFS: sda8: using ordered data mode
ReiserFS: sda8: journal params: device sda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda8: checking transaction log (sda8)
ReiserFS: sda8: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1461872k swap on /dev/sda9. Priority:-1 extents:1 across:1461872k
ADDRCONF(NETDEV_UP): eth0: link is not ready
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 17
[fglrx] GART Table is not in FRAME_BUFFER range
[fglrx] Reserve Block - 0 offset = 0X0 length = 0X40000
[fglrx] Reserve Block - 1 offset = 0X7ff5000 length = 0Xb000
hda-intel: Invalid position buffer, using LPIB read method instead.
scim-launcher[5739]: segfault at 0000000000000000 rip 0000000000000000 rsp 00007fff4dc073d8 error 14
[fglrx:firegl_addmap] *ERROR* existing map 0xffff810055f8d240 (handle 0xffffc20000371000)
[fglrx:firegl_addmap] *ERROR* existing map 0xffff810055f8d2c0 (handle 0x00000000)
[fglrx:firegl_addmap] *ERROR* existing map 0xffff810055f8d340 (handle 0xffffc20001840000)
[fglrx] PCIe has already been initialized. Reinitializing ...
[fglrx] GART Table is not in FRAME_BUFFER range
[fglrx] Reserve Block - 0 offset = 0X0 length = 0X40000
[fglrx] Reserve Block - 1 offset = 0X7ff5000 length = 0Xb000
scim-launcher[6210]: segfault at 0000000000000000 rip 0000000000000000 rsp 00007fff6581f608 error 14
[fglrx] PCIe has already been initialized. Reinitializing ...
[fglrx] GART Table is not in FRAME_BUFFER range
[fglrx] Reserve Block - 0 offset = 0X0 length = 0X40000
[fglrx] Reserve Block - 1 offset = 0X7ff5000 length = 0Xb000
audacious[6668]: segfault at ffffffffc02820e0 rip 00002aaab427f724 rsp 00007fff34f85ae0 error 4
audacious[7898]: segfault at ffffffffbc00f980 rip 00002aaab427f724 rsp 00007fffd0648e90 error 4
APIC error on CPU0: 00(40)
APIC error on CPU1: 00(40)
APIC error on CPU0: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU1: 40(40) |
|
IP卡
狗仔卡
发表于 2007-10-30 14:51:33
显身卡
发表于 2007-10-30 20:37:59