|
|
楼主 |
发表于 2003-1-19 21:53:59
|
显示全部楼层
编了好几次内核了，还是不行，我用的是2.4.18的内核
帮我看看
Linux version 2.4.18-2-gentoo (root@localhost) (gcc version 3.2.1 20021207 (Gentoo Linux 3.2.1-20021207)) #1 六 1月 18 02:18:43 UTC 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65520
zone(0): 4096 pages.
zone(1): 61424 pages.
zone(2): 0 pages.
Kernel command line: devfs=mount foo=bar root=/dev/hde5 vga=792 video=vesa:1024x768@70
Initializing CPU#0
Detected 1428.235 MHz processor.
Speakup v-1.00 CVS: Tue Jun 11 14:22:53 EDT 2002 : initialized
Console: colour dummy device 80x25
Calibrating delay loop... 2836.55 BogoMIPS
Memory: 253048k/262080k available (1339k kernel code, 6600k reserved, 1022k data, 168k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 4096 (order: 3, 32768 bytes)
ramfs: mounted with options: <defaults>
ramfs: max_pages=31886 max_file_pages=0 max_inodes=0 max_dentries=31886
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU: AMD Athlon(tm) XP 1600+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf9b50, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [1106/3189] at 00:00.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
speakup: initialized device: /dev/synth, node (MAJOR 10, MINOR 25)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
vesafb: framebuffer at 0xd8000000, mapped to 0xd080d000, size 32768k
vesafb: mode is 1024x768x32, linelength=4096, pages=1
vesafb: protected mode interface info at c000:c590
vesafb: scrolling: redraw
vesafb: directcolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
rivafb: cannot reserve FB region
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: 480 slots per queue, batch=120
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20265: IDE controller on PCI bus 00 dev 50
PDC20265: chipset revision 2
ide: Found promise 20265 in RAID mode.
PDC20265: not 100% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER Mode.
ide2: BM-DMA at 0xd000-0xd007, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xd008-0xd00f, BIOS settings: hdg:pio, hdh:pio
VP_IDE: IDE controller on PCI bus 00 dev 89
PCI: No IRQ known for interrupt pin A of device 00:11.1. Please try using pci=biosirq.
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xec00-0xec07, BIOS settings: hda MA, hdb:pio
ide1: BM-DMA at 0xec08-0xec0f, BIOS settings: hdcMA, hdd:pio
hda: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
hdc: ATAPI CDROM, ATAPI CD/DVD-ROM drive
hde: IC35L060AVER07-0, ATA DISK drive
hdg: ST320413A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xc000-0xc007,0xc402 on irq 11
ide3 at 0xc800-0xc807,0xcc02 on irq 11
blk: queue c03c192c, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03c192c, I/O limit 4095Mb (mask 0xffffffff)
hde: 120103200 sectors (61493 MB) w/1916KiB Cache, CHS=119150/16/63, UDMA(100)
blk: queue c03c1c70, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03c1c70, I/O limit 4095Mb (mask 0xffffffff)
hdg: 39102336 sectors (20020 MB) w/512KiB Cache, CHS=38792/16/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
/dev/ide/host2/bus0/target0/lun0: [PTBL] [7476/255/63] p1 p2 < p5 p6 p7 p8 p9 p10 p11 p12 p13 >
/dev/ide/host2/bus1/target0/lun0: [PTBL] [2434/255/63] p1 p2 p3 < p5 >
floppy0: no floppy controllers found
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 131072K size 1024 blocksize
loop: loaded (max 8 devices)
ide-floppy driver 0.99.newide
ataraid/d0: p1 p2 p3 < p5 >
Drive 0 is 19092 Mb (34 / 0)
Raid0 array consists of 1 drives.
Promise Fasttrak(tm) Softwareraid driver for linux version 0.03beta
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Couldn't find valid RAM disk image starting at 0.
Freeing initrd memory: 42k freed
VFS: Mounted root (ext2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 168k freed
Adding Swap: 514040k swap-space (priority -1)
8139too Fast Ethernet driver 0.9.25
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 Fast Ethernet at 0xd3859000, 00:e0:4c:11:7e:bb, IRQ 10
eth0: Identified 8139 chip type 'RTL-8139C'
SCSI subsystem driver Revision: 1.00
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 20:28:35 Jan 16 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xe400, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xe800, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4191 Mon Dec 9 11:49:01 PST 2002
devfs_register(nvidiactl): could not append to parent, err: -17
devfs_register(nvidia0): could not append to parent, err: -17
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide2(33,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide2(33,13), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver v1.1.22 [Flags: R/O MODULE]
NTFS: Warning! NTFS volume version is Win2k+: Mounting read-only
NTFS: Warning! NTFS volume version is Win2k+: Mounting read-only
NTFS: Warning! NTFS volume version is Win2k+: Mounting read-only
NTFS: Warning! NTFS volume version is Win2k+: Mounting read-only
MSDOS FS: IO charset cp936
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide3(34,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide3(34,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
divert: not allocating divert_blk for non-ethernet device ppp0
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack (2047 buckets, 16376 max)
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
/dev/vmnet: open called by PID 1403 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: up
bridge-eth0: attached
/dev/vmnet: open called by PID 1421 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 1692 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
divert: allocating divert_blk for vmnet8
/dev/vmnet: open called by PID 1703 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
NTFS: Name contains a character that cannot be converted to Unicode.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: Unsupported Via chipset (device id: 3189), you might want to try agp_try_unsupported=1.
agpgart: no supported devices found.
0: NVRM: AGPGART: unable to retrieve symbol table
hda: ATAPI 16X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.12
hdc: ATAPI CD-ROM drive, 128kB Cache
NTFS: Name contains a character that cannot be converted to Unicode.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: Unsupported Via chipset (device id: 3189), you might want to try agp_try_unsupported=1.
agpgart: no supported devices found.
0: NVRM: AGPGART: unable to retrieve symbol table
Unable to get major number 7 for loop device
Unable to get major number 7 for loop device
Unable to get major number 7 for loop device
Unable to get major number 7 for loop device
NTFS: Name contains a character that cannot be converted to Unicode.
NTFS: Name contains a character that cannot be converted to Unicode.
NTFS: Name contains a character that cannot be converted to Unicode.
OSS warning: Application xmame.SDL caused too many output underrun errors on audio device #1.
Look at oss/docs/README.performance for more info.
NET4: Linux IPX 0.47 for NET4.0
IPX Portions Copyright (c) 1995 Caldera, Inc.
IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
NET4: AppleTalk 0.18a for Linux NET4.0 |
|
IP卡
狗仔卡
发表于 2003-1-19 21:47:58
显身卡
发表于 2003-1-19 22:05:37