[求助]显卡驱动安装问题！

tulai

nvidia官方网站的instruction

It is recommended to use YOU (YaST Online Update) for (re)installation
of the nvidia driver. There are several reasons for this. First, it's
simple. Second, and this is the most important one, you won't need to
recompile the nvidia kernel module after a kernel update.

Inside YOU enable "Installable and Installed Patches" for "Show Patch
Category" and select "Download NVIDIA(r) Graphics Driver" from the
patches list (usually at the bottom of the list). Note, that you need
to mark it as "Update" (right mouse click) if you already installed it
before and the driver was uninstalled - for any reason. Proceed as
usual now. After YOU has finished restart your Xserver (i.e. logout
from your Xsession) and you're fine.

People who aren't afraid of recompiling the nvidia kernel module or
even reinstalling the nvidia driver each time the kernel has been
updated and want or need to use the latest and greatest nvidia driver
can use the following steps 1-3. The others should use the
instructions above using YOU and skip the steps below.

1) Kernel sources must be installed and configured. Usually this means
installing the 'kernel-source', 'make' and 'gcc' packages with YaST2.
Update it - if not already done - via YaST2 Online Update (YOU).

2) Use the nvidia installer for 1.0-7174.

modprobe agpgart   
sh NVIDIA-Linux-x86_64-1.0-7174-pkg2.run -q

3) Configure X.Org with

sax2 -m 0=nvidia (0 is a digit, not a letter!)

NOTE: There is no need to try to enable 3D support. It's already
      enabled, when the nvidia driver is running.



我现在suse还不能上网，只能选择第二种麻烦的方法，请问其中的（1）如何操作
1) Kernel sources must be installed and configured. Usually this means
installing the 'kernel-source', 'make' and 'gcc' packages with YaST2.
Update it - if not already done - via YaST2 Online Update (YOU).

troyme

这是安装的三个步骤
第一步，安装kernel-source', 'make' and 'gcc 这三个包，如果你有安装盘的话，这三个包里面都有的
第二步，执行命令 modprobe agpgart
sh NVIDIA-Linux-x86_64-1.0-7174-pkg2.run -q
你要下载NVIDIA-Linux-x86_64-1.0-7174-pkg2.run这个东西，NVIDIA网站上有
第三步 执行 sax2 -m 0=nvidia
估计是配置分辨率，刷新虑什么的，我没装过

tulai

Post by troyme
这是安装的三个步骤
第一步，安装kernel-source', 'make' and 'gcc 这三个包，如果你有安装盘的话，这三个包里面都有的
第二步，执行命令 modprobe agpgart
sh NVIDIA-Linux-x86_64-1.0-7174-pkg2.run -q
你要下载NVIDIA-Linux-x86_64-1.0-7174-pkg2.run这个东西，NVIDIA网站上有
第三步 执行 sax2 -m 0=nvidia
估计是配置分辨率，刷新虑什么的，我没装过

谢谢，这个我看的懂，我是想问问第一步具体怎么操作，我是新手，这三个包对应的rpm是哪个，会不会我再安装是已经装了，另外问问我是pcie的显卡，也是执行这个吗modprobe agpgart？

real_me

一般都装了，你试试看后面能执行的话就行了