|
在Fedora 中,一般如下设置:其实也是用的是rp-pppoe的,只是我们用的是图形界面设置。不知道他是用什么程序罢了。
应用程序──>系统工具──>互联网配置向导──>选xDXL。
输入:
1.提供商名称(填啥都可以的)
2.登录名
3.口令
最后要: 激活!
── 阿蟾 补充
rp-pppoe是linux最常用的pppoe拔号软件,几乎所有的发行版本都用这个,只是我们看到的配置界面不同罢了。从根本上来说没有什么不同,只是界面不同,但用命令行的adsl-setup来配置 ,所有都是一样的。
如何用rp-pppoe来拔号??
为什么要用rp-pppoe,有时Redhat/Fedora 的发行版中,adsl的pppoe拔号软件是rp-pppoe。在Redhat 8.0中会出现rp-pppoe的这个包出现BUG,所以我们有必要自己下载来安装rp-pppoe;
在Redhat中,我们可以用下面的命令来配制网卡的IP及DNS等。
#redhat-config-network
把IP和DNS设置成如下的。
IP地址:192.168.0.1
掩码:
255.255.255.0
DNS
202.96.134.133
202.96.168.68
在Fedora 4.0中调用网络设置的命令是(在菜单上也可以找到):
sh-3.00# system-config-network-tui
sh-3.00# system-config-network
不要设置网关
然后我们设置rp-pppoe,如果您没有adsl-setup这个命令,就要下载这个包;其实在网络设置中也有配置ADSL的拔号的,点几下鼠标就行了。下面是text模式的设置,所达到的目的是一样的;
http://www.roaringpenguin.com/penguin/pppoe/rp-pppoe-3.5.tar.gz
或者
http://www.roaringpenguin.com/pppoe/rp-pppoe-3.5.tar.gz
把老版本的rp-pppoe卸掉,如果有的话:
#rpm -e rp-pppoe
解压和安装:
#tar zxvf rp-pppoe-3.5.tar.gz
进入解压目录执行
#sh ./go
然后再来设置ADSL。这一处,我们要用命令。
#adsl-setup
Welcome to the Roaring Penguin ADSL client setup. First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...
Looks good! Now, please enter some information:
USER NAME
>>> Enter your PPPoE user name (default XXX): 在这里输入ADSL的用户名
INTERFACE
>>> Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default eth0):如果一张网卡就设置写上eth0
Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
>>> Enter the demand value (default no):不用写什么
DNS
Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here:在这里写上202.96.134.133
下一个DNS是202.96.168.68
PASSWORD
>>> Please enter your PPPoE password:输入密码
>>> Please re-enter your PPPoE password:再输入一次
FIREWALLING
Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.
The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
>>> Choose a type of firewall (0-2):这里添写为2
** Summary of what you entered **
Ethernet Interface: eth0
User name: XXX
Activate-on-demand: No
DNS: Do not adjust
Firewalling: MASQUERADE
>>> Accept these settings and adjust configuration files (y/n)?
弄完后,就按一个y键。
用adsl-start来启动ADSL。如果不成功就重启一下计算机。
adsl 相关的命令:
#adsl-start 打开ADSL
#adsl-stop 停止
#adsl-status 状态
北南 更改本帖
|
|