|
有时候开机启动失败,频率还挺高。提示如下:
- ACPI:PCI Interrupt 00000:00:1f.6[b]->link[PILB]->GSI 10(level, low)->IRQ 10
- ACPI:PCI Interrupt 00000:00:1f.5[b]->link[PILB]->GSI 10(level, low)->IRQ 10
- Unable to initialize codec #0
- ACPI:PCI Interrupt for device 00000:00:1f.6 disabled
- Intel ICH Modem: Probe of 00000:00:1f.6 failed with error -13
复制代码
熟悉硬件的朋友帮忙看看什么问题呢?
还有,每次启动完,都需要alsaconf才能使用声音,不知道跟这个有没有关系。
dmesg
- Linux version 2.6.15-1-686 (Debian 2.6.15-8) (waldi@debian.org) (gcc version 4.0.3 20060212 (prerelease) (Debian 4.0.2-9)) #2 Mon Mar 6 15:27:08 UTC 2006
- BIOS-provided physical RAM map:
- BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
- BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
- BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
- BIOS-e820: 0000000000100000 - 000000000f7e0000 (usable)
- BIOS-e820: 000000000f7e0000 - 000000000f7e8000 (ACPI data)
- BIOS-e820: 000000000f7e8000 - 000000000f800000 (ACPI NVS)
- BIOS-e820: 000000000f800000 - 0000000010000000 (reserved)
- BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
- 0MB HIGHMEM available.
- 247MB LOWMEM available.
- On node 0 totalpages: 63456
- DMA zone: 4096 pages, LIFO batch:0
- DMA32 zone: 0 pages, LIFO batch:0
- Normal zone: 59360 pages, LIFO batch:15
- HighMem zone: 0 pages, LIFO batch:0
- DMI 2.3 present.
- ACPI: RSDP (v000 Acer ) @ 0x000fe030
- ACPI: RSDT (v001 Acer FALCON3M 0x00000001 Acer 0x00000000) @ 0x0f7e0000
- ACPI: FADT (v001 Acer FALCON3M 0x00000001 Acer 0x00000000) @ 0x0f7e0054
- ACPI: BOOT (v001 Acer FALCON3M 0x00000001 Acer 0x00000000) @ 0x0f7e002c
- ACPI: DSDT (v001 Acer FALCON3M 0x00001000 MSFT 0x0100000d) @ 0x00000000
- ACPI: PM-Timer IO Port: 0xf108
- Allocating PCI resources starting at 20000000 (gap: 10000000:efff0000)
- Built 1 zonelists
- Kernel command line: root=/dev/hda7 ro
- Local APIC disabled by BIOS -- you can enable it with "lapic"
- mapped APIC to ffffd000 (011f1000)
- Initializing CPU#0
- PID hash table entries: 1024 (order: 10, 16384 bytes)
- Detected 1000.335 MHz processor.
- Using pmtmr for high-res timesource
- Console: colour VGA+ 80x25
- Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
- Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
- Memory: 244020k/253824k available (1425k kernel code, 9164k reserved, 530k data, 144k init, 0k highmem)
- Checking if this processor honours the WP bit even in supervisor mode... Ok.
- Calibrating delay using timer specific routine.. 2000.81 BogoMIPS (lpj=1000409)
- Security Framework v1.0.0 initialized
- SELinux: Disabled at boot.
- Capability LSM initialized
- Mount-cache hash table entries: 512
- CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
- CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
- CPU: L1 I cache: 16K, L1 D cache: 16K
- CPU: L2 cache: 512K
- CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
- Intel machine check architecture supported.
- Intel machine check reporting enabled on CPU#0.
- mtrr: v2.0 (20020519)
- CPU: Intel(R) Pentium(R) III Mobile CPU 1000MHz stepping 01
- Enabling fast FPU save and restore... done.
- Enabling unmasked SIMD FPU exception support... done.
- Checking 'hlt' instruction... OK.
- ACPI: setting ELCR to 0200 (from 0c00)
- checking if image is initramfs... it is
- Freeing initrd memory: 4578k freed
- NET: Registered protocol family 16
- ACPI: bus type pci registered
- PCI: PCI BIOS revision 2.10 entry at 0xf0200, last bus=1
- PCI: Using configuration type 1
- ACPI: Subsystem revision 20050902
- ACPI: Interpreter enabled
- ACPI: Using PIC for interrupt routing
- ACPI: PCI Root Bridge [PCI0] (0000:00)
- PCI: Probing PCI hardware (bus 00)
- ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
- Boot video device is 0000:00:02.0
- PCI quirk: region f100-f17f claimed by ICH4 ACPI/GPIO/TCO
- PCI quirk: region f200-f23f claimed by ICH4 GPIO
- PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
- PCI: Transparent bridge - 0000:00:1e.0
- ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
- ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
- ACPI: PCI Interrupt Link [PILA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
- ACPI: PCI Interrupt Link [PILB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
- ACPI: PCI Interrupt Link [PILC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
- ACPI: PCI Interrupt Link [PILD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
- ACPI: PCI Interrupt Link [PILE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
- ACPI: PCI Interrupt Link [PILF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
- ACPI: PCI Interrupt Link [PILG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
- ACPI: PCI Interrupt Link [PILH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
- ACPI: Embedded Controller [EC0] (gpe 29)
- Linux Plug and Play Support v0.97 (c) Adam Belay
- pnp: PnP ACPI init
- pnp: PnP ACPI: found 11 devices
- PnPBIOS: Disabled by ACPI PNP
- PCI: Using ACPI for IRQ routing
- PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
- pnp: 00:00: ioport range 0x7b0-0x7bb has been reserved
- pnp: 00:00: ioport range 0x7c0-0x7df has been reserved
- pnp: 00:00: ioport range 0xbb0-0xbbb has been reserved
- pnp: 00:00: ioport range 0xbc0-0xbdf has been reserved
- pnp: 00:00: ioport range 0xfb0-0xfbb has been reserved
- pnp: 00:00: ioport range 0xfc0-0xfdf has been reserved
- pnp: 00:00: ioport range 0x13b0-0x13bb has been reserved
- pnp: 00:00: ioport range 0x13c0-0x13df has been reserved
- pnp: 00:0a: ioport range 0xf100-0xf16f could not be reserved
- pnp: 00:0a: ioport range 0xf178-0xf17f has been reserved
- pnp: 00:0a: ioport range 0xf200-0xf23f has been reserved
- pnp: 00:0a: ioport range 0x380-0x38f has been reserved
- pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
- pnp: 00:0a: ioport range 0x580-0x587 has been reserved
- PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
- PCI: Bus 2, cardbus bridge: 0000:01:09.0
- IO window: 00009400-000094ff
- IO window: 00009800-000098ff
- PREFETCH window: 20000000-21ffffff
- MEM window: 24000000-25ffffff
- PCI: Bridge: 0000:00:1e.0
- IO window: 9000-9fff
- MEM window: a0100000-a01fffff
- PREFETCH window: 20000000-21ffffff
- PCI: Setting latency timer of device 0000:00:1e.0 to 64
- ACPI: PCI Interrupt Link [PILF] enabled at IRQ 10
- PCI: setting IRQ 10 as level-triggered
- ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [PILF] -> GSI 10 (level, low) -> IRQ 10
- Simple Boot Flag at 0x6e set to 0x1
- audit: initializing netlink socket (disabled)
- audit(1153241624.364:1): initialized
- VFS: Disk quotas dquot_6.5.1
- Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- Initializing Cryptographic API
- io scheduler noop registered
- io scheduler anticipatory registered
- io scheduler deadline registered
- io scheduler cfq registered
- isapnp: Scanning for PnP cards...
- isapnp: No Plug & Play device found
- PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
- i8042.c: Detected active multiplexing controller, rev 1.1.
- serio: i8042 AUX0 port at 0x60,0x64 irq 12
- serio: i8042 AUX1 port at 0x60,0x64 irq 12
- serio: i8042 AUX2 port at 0x60,0x64 irq 12
- serio: i8042 AUX3 port at 0x60,0x64 irq 12
- serio: i8042 KBD port at 0x60,0x64 irq 1
- Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
- serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
- 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
- ACPI: PCI Interrupt Link [PILB] enabled at IRQ 10
- ACPI: PCI Interrupt 0000:00:1f.6[b] -> Link [PILB] -> GSI 10 (level, low) -> IRQ 10
- ACPI: PCI interrupt for device 0000:00:1f.6 disabled
- RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
- NET: Registered protocol family 2
- IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
- TCP established hash table entries: 8192 (order: 3, 32768 bytes)
- TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
- TCP: Hash tables configured (established 8192 bind 8192)
- TCP reno registered
- TCP bic registered
- NET: Registered protocol family 1
- NET: Registered protocol family 17
- NET: Registered protocol family 8
- NET: Registered protocol family 20
- Using IPI Shortcut mode
- ACPI wakeup devices:
- SLPB OZ68 USB0 USB1 LID
- ACPI: (supports S0 S1 S3 S4 S5)
- Freeing unused kernel memory: 144k freed
- ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
- input: AT Translated Set 2 keyboard as /class/input/input0
- ACPI: Thermal Zone [THR1] (56 C)
- ACPI: Thermal Zone [THR2] (49 C)
- 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
- 8139cp: pci dev 0000:01:05.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
- 8139cp: Try the "8139too" driver instead.
- 8139too Fast Ethernet driver 0.9.27
- ACPI: PCI Interrupt Link [PILC] enabled at IRQ 11
- PCI: setting IRQ 11 as level-triggered
- ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [PILC] -> GSI 11 (level, low) -> IRQ 11
- eth0: RealTek RTL8139 at 0x9000, 00:00:e2:6b:c6:a0, IRQ 11
- eth0: Identified 8139 chip type 'RTL-8100'
- Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
- ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
- ICH3M: IDE controller at PCI slot 0000:00:1f.1
- ACPI: PCI Interrupt 0000:00:1f.1[A]: no GSI
- ICH3M: chipset revision 2
- ICH3M: not 100% native mode: will probe irqs later
- ide0: BM-DMA at 0xb060-0xb067, BIOS settings: hda:DMA, hdb:pio
- ide1: BM-DMA at 0xb068-0xb06f, BIOS settings: hdc:DMA, hdd:pio
- Probing IDE interface ide0...
- usbcore: registered new driver usbfs
- usbcore: registered new driver hub
- USB Universal Host Controller Interface driver v2.3
- ACPI: PCI Interrupt Link [PILA] enabled at IRQ 11
- ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [PILA] -> GSI 11 (level, low) -> IRQ 11
- PCI: Setting latency timer of device 0000:00:1d.0 to 64
- uhci_hcd 0000:00:1d.0: UHCI Host Controller
- uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
- uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000aca0
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 2 ports detected
- ACPI: PCI Interrupt Link [PILD] enabled at IRQ 11
- ACPI: PCI Interrupt 0000:00:1d.1[b] -> Link [PILD] -> GSI 11 (level, low) -> IRQ 11
- PCI: Setting latency timer of device 0000:00:1d.1 to 64
- uhci_hcd 0000:00:1d.1: UHCI Host Controller
- uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
- uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000ace0
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 2 ports detected
- hda: ST9408114A, ATA DISK drive
- usb 1-1: new full speed USB device using uhci_hcd and address 2
- ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
- Probing IDE interface ide1...
- hdc: SR243T1, ATAPI CD/DVD-ROM drive
- ide1 at 0x170-0x177,0x376 on irq 15
- hda: max request size: 1024KiB
- SCSI subsystem initialized
- Initializing USB Mass Storage driver...
- scsi0 : SCSI emulation for USB Mass Storage devices
- usbcore: registered new driver usb-storage
- USB Mass Storage support registered.
- usb-storage: device found at 2
- usb-storage: waiting for device to settle before scanning
- hda: 78140160 sectors (40007 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
- hda: cache flushes supported
- hda: hda1 hda2 < hda5 hda6 hda7 >
- hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
- Uniform CD-ROM driver Revision: 3.20
- Attempting manual resume
- kjournald starting. Commit interval 5 seconds
- EXT3-fs: mounted filesystem with ordered data mode.
- mice: PS/2 mouse device common for all mice
- Floppy drive(s): fd0 is 1.44M
- FDC 0 is a post-1991 82077
- Vendor: IC25N020 Model: ATMR04-0 Rev: MO1O
- Type: Direct-Access ANSI SCSI revision: 00
- usb-storage: device scan complete
- Synaptics Touchpad, model: 1, fw: 4.6, id: 0x925ea1, caps: 0x80471b/0x0
- input: SynPS/2 Synaptics TouchPad as /class/input/input1
- input: PC Speaker as /class/input/input2
- Real Time Clock Driver v1.12
- pnp: Device 00:06 activated.
- parport: PnPBIOS parport detected.
- parport0: PC-style at 0x378, irq 5 [PCSPP,TRISTATE,EPP]
- ACPI: PCI Interrupt 0000:00:1f.5[b] -> Link [PILB] -> GSI 10 (level, low) -> IRQ 10
- PCI: Setting latency timer of device 0000:00:1f.5 to 64
- intel8x0_measure_ac97_clock: measured 50488 usecs
- intel8x0: clocking to 48000
- ACPI: PCI Interrupt 0000:00:1f.6[b] -> Link [PILB] -> GSI 10 (level, low) -> IRQ 10
- PCI: Setting latency timer of device 0000:00:1f.6 to 64
- Linux agpgart interface v0.101 (c) Dave Jones
- agpgart: Detected an Intel 830M Chipset.
- agpgart: Detected 8060K stolen memory.
- agpgart: AGP aperture is 128M @ 0x98000000
- Unable to initialize codec #0
- ACPI: PCI interrupt for device 0000:00:1f.6 disabled
- Intel ICH Modem: probe of 0000:00:1f.6 failed with error -13
- ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [PILF] -> GSI 10 (level, low) -> IRQ 10
- Yenta: CardBus bridge found at 0000:01:09.0 [1025:1024]
- Yenta O2: res at 0x94/0xD4: 00/ea
- Yenta O2: enabling read prefetch/write burst
- Yenta: ISA IRQ mask 0x0098, PCI irq 10
- Socket status: 30000007
- pcmcia: parent PCI bridge I/O window: 0x9000 - 0x9fff
- cs: IO port probe 0x9000-0x9fff: clean.
- pcmcia: parent PCI bridge Memory window: 0xa0100000 - 0xa01fffff
- pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x21ffffff
- SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
- sda: assuming drive cache: write through
- SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
- sda: assuming drive cache: write through
- sda:<6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
- shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
- sda1 sda2 < sda5 >
- sd 0:0:0:0: Attached scsi disk sda
- hw_random: RNG not detected
- codec_write 0: semaphore is not ready for register 0x2
- codec_write 0: semaphore is not ready for register 0x2
- codec_write 0: semaphore is not ready for register 0x4
- codec_write 0: semaphore is not ready for register 0x4
- codec_write 0: semaphore is not ready for register 0x6
- codec_write 0: semaphore is not ready for register 0x6
- codec_write 0: semaphore is not ready for register 0x10
- codec_write 0: semaphore is not ready for register 0x12
- codec_write 0: semaphore is not ready for register 0x12
- codec_write 0: semaphore is not ready for register 0x18
- codec_write 0: semaphore is not ready for register 0x18
- codec_write 0: semaphore is not ready for register 0x68
- cs: IO port probe 0x100-0x3af: clean.
- cs: IO port probe 0x3e0-0x4ff: clean.
- cs: IO port probe 0x820-0x8ff: clean.
- cs: IO port probe 0xc00-0xcf7: clean.
- cs: IO port probe 0xa00-0xaff: clean.
- Adding 522072k swap on /dev/hda6. Priority:-1 extents:1 across:522072k
- EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
- EXT3 FS on hda7, internal journal
- device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
- pcmcia: Detected deprecated PCMCIA ioctl usage.
- pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
- pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
- eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
- ACPI: Battery Slot [BAT0] (battery present)
- ACPI: AC Adapter [AC] (on-line)
- ACPI: Power Button (FF) [PWRF]
- ACPI: Sleep Button (CM) [SLPB]
- ACPI: Lid Switch [LID]
- NET: Registered protocol family 10
- lo: Disabled Privacy Extensions
- IPv6 over IPv4 tunneling driver
- eth0: no IPv6 routers present
复制代码 |
|