音频CD刻录失败,连坏两张盘子! [问题解决,对你有用,一定要看]

loujch · 发表于 2007-4-18 22:03:47

以前正常,这次重装了一下系统(用0.8装然后升级成最新),出问题了!
[安装前后的区别在于/dev/hda和/dev/hdc变成了/dev/sda和/dev/sr0,是不是这个原因?]

出错信息: (软件是gnomebaker)

wodim: No write mode specified.
wodim: Asuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
scsidev: '1,0,0'
scsibus: 1 target: 0 lun: 0
Linux sg driver version: 3.5.34
Wodim version: 1.1.2
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 0 = CD-DA
atapi: 1
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'HL-DT-ST'
Identification : 'DVDRAM GSA-H42N '
Revision : 'RL00'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0016 (DVD-R/DL layer jump recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x001A (DVD+RW)
Profile: 0x001B (DVD+R)
Profile: 0x002B (DVD+R/DL)
Profile: 0x0010 (DVD-ROM)
Profile: 0x0009 (CD-R)
Profile: 0x000A (CD-RW) (current)
Profile: 0x0008 (CD-ROM)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1053696 = 1029 KB
Drive DMA Speed: 14054 kB/s 79x CD 10x DVD
FIFO size : 4194304 = 4096 KB
6
recommended erase/write power: 5
A1 values: 24 2C DC
A2 values: 14 A4 4A
A3 values: 04 C4 80
Disk type: Phase change
Manuf. index: 11
Manufacturer: Mitsubishi Chemical Corporation
Blocks total: 336075 Blocks current: 336075 Blocks remaining: 132528
Starting to write CD/DVD at speed 10.0 in real TAO mode for single session.
Last chance to quit, starting real write in 5 seconds.Speed set to 1764 KB/s
4 seconds. 3 seconds. 2 seconds. 1 seconds. 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB: 2A 00 00 00 00 00 00 00 1B 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 2A 00 00 90 30 05 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x30 Qual 0x05 (cannot write medium - incompatible format) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 63504
cmd finished after 0.002s timeout 40s
wodim: A write error occured.
wodim: Please properly read the error message above.
write track data: error after 0 bytes
Writing time: 5.090s
Average write speed 538.8x.
Fixating...
Fixating time: 0.005s
Errno: 5 (Input/output error), close track/session scsi sendcmd: no error
CDB: 5B 00 02 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 5B 00 00 90 30 05 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x30 Qual 0x05 (cannot write medium - incompatible format) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.002s timeout 480s
cmd finished after 0.002s timeout 480s
wodim: Cannot fixate disk.

复制代码

loujch · 发表于 2007-4-18 22:07:31

又用cd-rw试了一下,刻数据CD也失败!

难免有错 · 发表于 2007-4-18 23:16:52

没有啊，我的还是hdc

terabithia · 发表于 2007-4-19 00:27:04

应该跟名字的变化没关系

晨想 · 发表于 2007-4-19 00:41:14

应该是没关系的，我的就是 sr0，没问题的说。

用 scsi 的东西驱动了，和 sdx 的原理一样。

难免有错 · 发表于 2007-4-19 01:00:34

我一般用cdrecord,还没刻坏过的记录。

loujch · 发表于 2007-4-19 08:13:44

Post by 难免有错
我一般用cdrecord,还没刻坏过的记录。

我用cdrecord刻录,报一样的错误信息!

实验过了,用0.7.2安装再升级,/dev/hda和/dev/hdc的情况下也一样,看样子刻录机有问题或者arch最新的升级包有问题!

不会是好久以前mandrake9.1导致LG光驱损坏事件重演吧?我是LG刻录机!

ys_freedom · 发表于 2007-4-19 11:22:59

我fstab里面光驱还是hdx，昨天刚刚刻了一张盘...

loujch · 发表于 2007-4-19 13:26:14

我fstab里没有写入光驱信息,我是用hal自动挂载的

blance · 发表于 2007-4-19 13:45:03

一直用k3b，没烧坏过一张盘

		自动登录	找回密码
密码			注册