|
次此使用是使用rtorrent来作的客户端。
使用的是 jeff-cao 兄弟的 种子.
连接如下 http://www.linuxsir.cn/bbs/thread331144.html
如果你已经用第一个种子连接到 99%了,并且没有动静,那么请下载第二个种子。
并且进行下载 第二个种子。 当有输出文件的时候,停止下载。
把第一个种子下载的 99%的文件替换过来。 要求文件名称一样。
然后等待 hash 完毕。 然后会下载完成!!
至于使用迅雷或者 BT精灵之类WINDOWS的应用程序,一般后面有后缀名称。
把后缀名称改掉看看能否使用这个方法。
rtorrent .conf 如下- # This is an example resource file for rTorrent. Copy to
- # ~/.rtorrent.rc and enable/modify the options as needed. Remember to
- # uncomment the options you wish to enable.
- # Minumum amount of peers to connect per torrent, if available.
- min_peers = 20
- # Minumum amount of peers to connect per torrent.
- max_peers = 100
- # Same as above but for seeding completed torrents (-1 = same as downloading)
- #min_peers_seed = 10
- #max_peers_seed = 20
- # Maximum number of simultanious uploads per torrent.
- max_uploads = 10
- # Global download rate in KiB. "0" for unlimited.
- download_rate = 80
- # Global upload rate in KiB. "0" for unlimited.
- upload_rate = 30
- # Default directory to save downloaded files. Note it doesn't support
- # space yet.
- directory = /jffs/Public/BT 改成自己目录
- # Watch a directory for new torrents, and stop those that have been deleted.
- schedule = watch_directory,5,5,load_start=/jffs/Public/BT/dl/*.torrent
- schedule = untied_directory,5,5,stop_untied=
- # Close torrents when diskspace is low.
- #schedule = low_diskspace,5,60,close_low_diskspace=100M
- # Default session directory. Make sure you don't run multiple instance
- # of rtorrent using the same session directory. Perhaps using a
- # relative path?
- session = /jffs/Public/BT/session 改成自己目录
- # The ip address reported to the tracker.
- #ip = rakshasa
- # The ip address the listening socket and outgoing connections is
- # bound to.
- #bind = rakshasa
- # Port range to use for listening.
- port_range = 51777-51780
- # Start opening ports at a random position within the port range.
- #port_random = no
- # Check hash for finished torrents. Might be usefull until the bug is
- # fixed that causes lack of diskspace not to be properly reported.
- #check_hash = no
- # Set whetever the client should try to connect to UDP trackers.
- use_udp_trackers = yes
- # Alternative calls to bind and ip that should handle dynamic ip's.
- #schedule = ip_tick,0,1800,ip=rakshasa
- #schedule = bind_tick,0,1800,bind=rakshasa
- #
- # Do not modify the following parameters unless you know what you're doing.
- #
- # Hash read-ahead controls how many MB to request the kernel to read
- # ahead. If the value is too low the disk may not be fully utilized,
- # while if too high the kernel might not be able to keep the read
- # pages in memory thus end up trashing.
- #hash_read_ahead = 10
- # Interval between attempts to check the hash, in milliseconds.
- #hash_interval = 100
- # Number of attempts to check the hash while using the mincore status,
- # before forcing. Overworked systems might need lower values to get a
- # decent hash checking rate.
- #hash_max_tries = 10
- # Max number of files to keep open simultaniously.
- #max_open_files = 128
- # Number of sockets to simultaneously keep open.
- #max_open_sockets = <no default>
- # Example of scheduling commands: Switch between two ip's every 5
- # seconds.
- #schedule = "ip_tick1,5,10,ip=torretta"
- #schedule = "ip_tick2,10,10,ip=lampedusa"
- # Remove a scheduled event.
- #schedule_remove = "ip_tick1"
- # Stop torrents when reaching upload ratio in percent,
- # when also reaching total upload in bytes, or when
- # reaching final upload ratio in percent.
- # example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
- #schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"
- schedule = ratio,30,60,stop_on_ratio=200
- # Encryption options, set to none (default) or any combination of the following:
- # allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
- #
- # The example value allows incoming encrypted connections, starts unencrypted
- # outgoing connections but retries with encryption if they fail, preferring
- # plaintext to RC4 encryption after the encrypted handshake
- #
- encryption = allow_incoming,enable_retry,prefer_plaintext
- # Enable DHT support for trackerless torrents or when all trackers are down.
- # May be set to "disable" (completely disable DHT), "off" (do not start DHT),
- # "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
- # The default is "off". For DHT to work, a session directory must be defined.
- #
- #dht = on
- # UDP port to use for DHT.
- #
- #dht_port = 6885
- # Enable peer exchange (for torrents not marked private)
- #
- peer_exchange = yes
- #
- # Do not modify the following parameters unless you know what you're doing.
- #
- #scgi_port = :5000
- #umask =0000
- #encoding_list = UTF-8
- #scgi_local = /opt/var/run/rpc.socket
复制代码 $ rtorrent -n -o import=/opt/etc/rtorrent.conf
也可以这样调用 config文件
http://discuz.orz101.com/viewthr ... &extra=page%3D1
是rtorrent 和 screent 使用方法。
我已经安装了 suse 11了!! KDE 4.0 果然不错!! 呱呱!! |
|