我这样是否就算安装成功了呢? 我在kppp里查询不到我的modem.
我modem 在win98下是com3
-----------------------------------------------------------
ot@localhost rpm]# rpm -ivh ltmodem-kv_2.4.18_5-8.22a5-1.i386.rpm
Preparing... ########################################### [100%]
1:ltmodem-kv_2.4.18_5 ########################################### [100%]
... using /sbin/lspci
By the Class 07nn: criteria, detected system PCI modem devices are:
device Class VendorIDeviceID == ModemID
----------------------------------------------------------------
00:0f.0 Class 0780: 11c1:0440 (rev 01)
00:0f.0 Communication controller: Lucent Microelectronics 56k WinModem (rev 01)
VENDOR 0x11c1 DEVICE 0x0440
ID are within the serviced ranges:
A supported DSP Modem verified:
MODEM_ID=11c1:0440
IDs of supported Lucent DSP PCI modems have ranges:
Vendor vendor_id device_id range
-----------------------------------------------
LUCENT 0x11c1 0x0440-0x045c
XIRCOM 0x115d 0x0000-0x000F
XIRCOM 0x115d 0x0440-0x045c
XIRCOM 0x115d 0x0010-0x03ff
To see detailed information on 11c1:0440
Copying this detailed information to /usr/share/doc/ltmodem-kv_2.4.18_5-8.22a5/LTinstall.txt
----------------------------------------------
MODEL_DATA= 0x0440 -- Mars 2 - data/fax/voice
00:0f.0 Communication controller: Lucent Microelectronics 56k WinModem (rev 01)
00:0f.0 Class 0780: 11c1:0440 (rev 01)
Subsystem: 11c1:0440
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <ERR-
Latency: 0 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at dfffff00 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at cc00
Region 2: I/O ports at c800 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
----------------------------------------------
Checking for Lucent DSP modem
... using /sbin/lspci
By the Class 07nn: criteria, detected system PCI modem devices are:
device Class VendorIDeviceID == ModemID
----------------------------------------------------------------
00:0f.0 Class 0780: 11c1:0440 (rev 01)
00:0f.0 Communication controller: Lucent Microelectronics 56k WinModem (rev 01)
VENDOR 0x11c1 DEVICE 0x0440
ID are within the serviced ranges:
A supported DSP Modem verified:
MODEM_ID=11c1:0440
IDs of supported Lucent DSP PCI modems have ranges:
Vendor vendor_id device_id range
-----------------------------------------------
LUCENT 0x11c1 0x0440-0x045c
XIRCOM 0x115d 0x0000-0x000F
XIRCOM 0x115d 0x0440-0x045c
XIRCOM 0x115d 0x0010-0x03ff
To see detailed information on 11c1:0440
Copying this detailed information to /usr/share/doc/ltmodem-kv_2.4.18_5-8.22a5/LTinstall.txt
----------------------------------------------
MODEL_DATA= 0x0440 -- Mars 2 - data/fax/voice
00:0f.0 Communication controller: Lucent Microelectronics 56k WinModem (rev 01)
00:0f.0 Class 0780: 11c1:0440 (rev 01)
Subsystem: 11c1:0440
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <ERR-
Latency: 0 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at dfffff00 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at cc00
Region 2: I/O ports at c800 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
----------------------------------------------
scanPCI finished, proceeding with autoload section
Made modem device node /dev/ttyLT0
group ownership set to uucp
with symbolic link /dev/modem --> /dev/ttyLT0
Writing modules autoloading lines to /etc/modules.conf:
Updating with: depmod -a
Capturing output to /tmp/ltmodem/tmpfile and parsing.
The modem drivers dependencies are properly resolved.
A folder has been installed in your Systems documentation,
/usr/share/doc/ltmodem-kv_2.4.18_5-8.22a5
containing much useful guidance and uilities. Updates can be
downloaded from http://www.heby.de/ltmodem/ as DOCs.tgz
To get online, the Port to be specified in your dialout scripts is:
/dev/ttyLT0 or its symbolic, /dev/modem
A summary of installation actions with Advice is contained in: /usr/share/doc/ltmodem-kv_2.4.18_5-8.22a5/LTinstall.txt
Browse DOCs/Ltmodem.html for issues that may be relevant to your system and useful URLs
Also see DOCs/LastAdvice
Some dialer utilities including KPPP require that Each User set up a configuration,
as there could be diverse configurations on multi-User systems.
Read DOCs/wvdial.txt for aid in configuring the smart dialup utility, WVDIAL
Otherwise, get Online and Enjoy
Relate problems to discuss@linmodems.org
Gratitude too, to discuss@linmodems.org
If not familar with the ltmodem drivers, run the interactive CHECKOUT utility by executing:
/usr/share/doc/ltmodem-kv_2.4.18_5-8.22a5/utils/checkout |