好晕，终于搞定了Mandriva2006的pppoe连接

notomorrow

用Mandriva控制中心的向导怎么配置怎么不行
我干脆不用向导了  :rolleyes:
跑到软件管理里面安装  rp-pppoe-3.5-5mdk.i586.rpm
然后
su
cd /sbin
adsl-setup
接下来输入用户名之类的信息
adsl-start
连接成功

[root@kaizi sbin]# adsl-setup
Welcome to the Roaring Penguin ADSL client setup.  First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...

Looks good!  Now, please enter some information:

USER NAME

>>> Enter your PPPoE user name (default bxxxnxnx@sympatico.ca): k9052067@fztt2

INTERFACE

>>> Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default eth0): eth0

Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped.  If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses.  You may have some problems with demand-activated links.
>>> Enter the demand value (default no): no

DNS

Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here: server

PASSWORD

>>> Please enter your PPPoE password:
>>> Please re-enter your PPPoE password:

FIREWALLING

Please choose the firewall rules to use.  Note that these rules are
very basic.  You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security.  If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself.  Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc.  If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.

The firewall choices are:
0 - NONE: This script will not set any firewall rules.  You are responsible
          for ensuring the security of your machine.  You are STRONGLY
          recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
                for a LAN
>>> Choose a type of firewall (0-2): 0

** Summary of what you entered **

Ethernet Interface: eth0
User name:          k9052067@fztt2
Activate-on-demand: No
DNS addresses:      Supplied by ISP's server
Firewalling:        NONE

>>> Accept these settings and adjust configuration files (y/n)? y
Adjusting /etc/ppp/pppoe.conf
Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets
  (But first backing it up to /etc/ppp/pap-secrets-bak)
  (But first backing it up to /etc/ppp/chap-secrets-bak)



Congratulations, it should be all set up!

Type 'adsl-start' to bring up your ADSL link and 'adsl-stop' to bring
it down.  Type 'adsl-status' to see the link status.
[root@kaizi sbin]# adsl
adsl-connect  adsl-setup    adsl-start    adsl-status   adsl-stop
[root@kaizi sbin]# adsl-start
.. Connected!
[root@kaizi sbin]# adsl-st
adsl-start   adsl-status  adsl-stop
[root@kaizi sbin]# adsl-status
adsl-status: Link is up and running on interface ppp0
ppp0      Link encapoint-to-Point Protocol
          inet addr:125.213.2.57  P-t-P:125.213.0.1  Mask:255.255.255.255
          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1492  Metric:1
          RX packets:4 errors:0 dropped:0 overruns:0 frame:0
          TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:3
          RX bytes:102 (102.0 b)  TX bytes:134 (134.0 b)

有图为证：

catfox2

是这样的，呵呵。
向导这样种种还是少用为好。

Daring666

应该是那个向导不完善，如果安装时不配置adsl那么相关组件就不会安装，安装后用那个向导配置，大概是它没把组件安完整，所有无法配置成功

kukukuan

这个问题我也遇到过，后来重装后所有ADSL的选择项都选是，让他开机 就启动，就莫名其妙的好了