方正文杰A280E打印机怎么驱动？(设备是好的！哈哈 )

zhanguo

没有啊 ！老大 ，谢谢 你  真地~

北南南北

国产的东西看来就是有点麻烦

请用这个打印机的弟兄来帮助一下吧

#lspci 这个能不能看出来点？？

zhanguo

[root@zhanguo root]# lspci
00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory Contro
ller Hub (rev 02)
00:02.0 VGA compatible controller: Intel Corp. 82815 CGC [Chipset Graphics Contr
oller] (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev 01)
00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 01)
00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 01)
00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 01)
00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 01)
00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 01)
00:1f.5 Multimedia audio controller: Intel Corp. 82801BA/BAM AC'97 Audio (rev 01
)
01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
[root@zhanguo root]#

哈哈，又骚扰大家了，看看吧老大，我是没看出来！
[root@zhanguo root]# lspci -v
00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory Controller Hub (rev 02)
        Subsystem: Intel Corp. 82815 815 Chipset Host Bridge and Memory Controller Hub
        Flags: bus master, fast devsel, latency 0
        Capabilities: [88] #09 [f104]

00:02.0 VGA compatible controller: Intel Corp. 82815 CGC [Chipset Graphics Controller] (rev 02) (prog-if 00 [VGA])
        Subsystem: Intel Corp. 82815 CGC [Chipset Graphics Controller]
        Flags: bus master, 66Mhz, medium devsel, latency 0, IRQ 11
        Memory at d0000000 (32-bit, prefetchable) [size=64M]
        Memory at d5000000 (32-bit, non-prefetchable) [size=512K]
        Capabilities: [dc] Power Management version 2

00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev 01) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
        I/O behind bridge: 0000c000-0000cfff
        Memory behind bridge: d4000000-d4ffffff

00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 01)
        Flags: bus master, medium devsel, latency 0

00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 01) (prog-if 80 [Master])
        Subsystem: Intel Corp.: Unknown device 2440
        Flags: bus master, medium devsel, latency 0
        I/O ports at f000

00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 01) (prog-if 00 [UHCI])
        Subsystem: Intel Corp.: Unknown device 2440
        Flags: bus master, medium devsel, latency 0, IRQ 11
        I/O ports at d000

00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 01)
        Subsystem: Intel Corp.: Unknown device 2440
        Flags: medium devsel, IRQ 5
        I/O ports at 5000

00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 01) (prog-if 00 [UHCI])
        Subsystem: Intel Corp.: Unknown device 2440
        Flags: bus master, medium devsel, latency 0, IRQ 9
        I/O ports at d400

00:1f.5 Multimedia audio controller: Intel Corp. 82801BA/BAM AC'97 Audio (rev 01)
        Subsystem: Analog Devices: Unknown device 5348
        Flags: bus master, medium devsel, latency 0, IRQ 5
        I/O ports at d800 [size=256]
        I/O ports at dc00

01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
        Flags: medium devsel, IRQ 11
        I/O ports at c000
        Expansion ROM at <unassigned> [disabled] [size=16K]

北南南北

我也看不出来了，
不知道他用的是什么芯片，能否把他用的win的驱动地址给我一个链接？？

多谢

zhanguo

大哥，你可以到官方网站去下载。

qqlong

楼上的兄弟我很同情你，我用的是方正的文景A220、文杰a6100u两款打印机，和你一样找不到驱动如果我没记错的话，您在www.linuxfans.org里面也发了 ... inux驱动试试！

qqlong

我知道我用的文杰a6100u这款打印机是hp的5100改版，我建议你找一些惠普打印机的驱动先在windows里面试一下，如果兼容的话，在下载linux驱动试试！

zhanguo

楼上兄弟，我感激不尽。
我马上试试，结果我会告之与你！
thanks a billion