在Red hat Linux7.3中怎样按装CONEXANT芯片的内置猫

zwx

youwater你好：
很感谢你多次的帮助，但我真的是刚接触Red hat linux7.3的系统，一点知识都没有，能具体说说在那里下载的驱动，和如何按装，越具体越好！真的很感谢各位关心的人

zwx

型号：conexant
hsfi
cx11252-11
E143146.1
0130
MEXICO
我把芯片上的字都写上了此内猫是插在PCI上的
CPU是CELERON 733MHZ
主板是M-ATX是集成810

北南南北

把rpm包先卸载，用
#rpm -e 文件名
比如我安装了G五笔的rpm包，现在想卸载用下面的命令，
#rpm -e gWuBi
通过这个例子来卸载你已经安装过的RPM包。

然后下载.tar.gz兄，看里面的README和INSTALL来做。试一下。

zwx

在那里下载tar.gz的包？网址

北南南北

http://www.mbsi.ca/cnxtlindrv/hcf/downloads.html

zwx

具体怎么来按装这个tar.gz的包，我看了基础教程也不太懂，希望能开个小灶，具体说说怎么装，谢谢了，还有怎么解压这个文件，谢谢了

北南南北

#tar zxvf *.tar.gz

zwx

真的不好意思，又来取经了
太难了，不知道不还是我太笨了：）
能在图形界面下安装.tar.gz包，具体怎么装能细一点吗？

祝大家幸福快乐，特别是 北南南北 的热情关怀，真的很感激很感激！

北南南北

看一下里面的README和INSTALL
这个是没有图形的，只能用命令来安装。。。

#tar zxvf hcfpcimodem-0.98mbsibeta02101002.tar.gz
#cd hcfpcimodem-0.98mbsibeta02101002
#make install
#hcfpciconfig

北南南北

cfusbconfig --help" for the USB version) for usage information.


CHANGING THE COUNTRY PARAMETER

With "hcfpciconfig --country" ("hcfusbconfig --country" for the USB version)
you may select another country supported by your modem.


MANUALLY UNLOADING THE DRIVERS

The modem drivers can be manually unloaded using the "hcfpcistop"
("hcfusbstop" for the USB version) command.


USING ALTERNATIVE VENDOR AND DEVICE IDS

If your modem uses a chipset supported by the drivers but isn't
recognized by the supplied .inf files, you may use (at your own risk)
"hcf{pci|usb}config --hwtype" to explicitly configure the vendor and
device IDs of your modem.


DOCUMENTATION

See the included document 100498D_RM_HxF_Released.pdf (viewable with
Adobe Acrobat reader or other PDF readers).


REMOVING THE DRIVER

If for any reason you wish to un-install the HCF drivers from your
system, the proper way to proceed depends on how they were initially
installed.

If you used an RPM installation method, execute "rpm -e hcfpcimodem"
("rpm -e hcfusbmodem" for the USB version) to remove the package.
If you used the tar method, change your current directory to where
you extracted the archive, and execute "make uninstall"


MORE INFORMATION AND HELP

If you require assistance or need more information, go to:
              http://www.mbsi.ca/cnxtlindrv

Conexant Systems neither distributes nor maintains this package.
PLEASE DO NOT CONTACT CONEXANT REGARDING THIS SOFTWARE!!!


BUGS

A list of currently known problems is included in the file "BUGS".


BAD CONNECTIONS

If you experience sudden disconnects or bad connections, please check
the last call status information, which can be obtained with the
AT#UG command or "cat /proc/driver/hcf/0/lastcallstatus" (2.4 or later).
Alternatively the driver can be configured to automatically log
this data upon carrier loss by adding the "loglastcallstatus=1" parameter
to the "options hcfserial" line in /etc/modules.conf.


REPORTING PROBLEMS

Additional problem reports or patches may be sent to: hcflinux-bugs@mbsi.ca

Enclosing the output of "hcfpciconfig --dumpdiag"
("hcfusbconfig --dumpdiag" for the USB version) and the last call status
information if pertinent (see above) in your report can greatly
facilitate problem resolution.