[求助]如何安装网卡？？

逸飞

有两台机子联网，一台redhat/2000，一台xp。2000-xp联网正常，网卡无故障。linux下，网卡配置完后，linux-xp相互可以ping通，网卡配置正确，但是我修改完域名和主机名后，就出问题了，两个机子不能ping通，netcfg,显示的eth0 inactive,lo active,将eth0 改为active 保存，显示没有此设备   这个问题该咋解决？？那位高人能教教我。

pandonny

教你一个最简单的方法,把Linux的网卡拔下,然后开机系统会提示网卡设备没有监测到,问你是否删除此设备,回答是.
然后关机,再把网卡插上去,系统启动的时候会提示监测到网卡,然后选择配置就ok了

逸飞

谢了，pandonny  我试试

逸飞

[这个贴子最后由逸飞在 2002/04/24 09:50am 编辑]

pandonny兄，问题还是没有解决！！
我按你的方法把Linux的网卡拔下,然后开机系统会提示网卡设备没有监测到,问你是否删除此设备,回答是. 然后关机,再把网卡插上去,系统启动的时候会提示监测到网卡,然后选择配置，系统好像提示已存在配置，是否要替代，我没有仔细看，就选ok，然后就有回到以前的情况了！！！
modules.conf文件能否删掉，
#cat modules.conf
alias parport-lowlevel parport-pc
alias usb-controller usb-uhci
options ne2k-pci io=0xcc00 irq=10
post-install mad16/sbin/modprobe "aci"
options mad16 io=0x600 irq=10 dma=0 dma16=0
       mpu-io=0x330 mpu-irq=10
alias sound-slot-0 via82cXXX
option sb support=1
alias eth0 ne2k-pic<p>帮我解释解释！！谢了！！<p>问题二：
#netcfg
&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; *********** Network Configurator***********
----------------------------------------------------------------------------
Names &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; hosts &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; interfaces &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;routing
inter &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; ip &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; proto &nbsp; &nbsp; &nbsp; atboot &nbsp; &nbsp; &nbsp; &nbsp; active
lo &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;127.0.0.1 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;none &nbsp; &nbsp; &nbsp; &nbsp; yes &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;active
eth0 &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;192.168.0.1 &nbsp; &nbsp; &nbsp; &nbsp;none &nbsp; &nbsp; &nbsp; &nbsp; yes &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;inactive
----------------------------------------------------------------------------
&nbsp; &nbsp; &nbsp;add &nbsp; &nbsp; &nbsp;edit &nbsp; &nbsp; &nbsp; &nbsp;del &nbsp; &nbsp; &nbsp; &nbsp;active ..........
----------------------------------------------------------------------------
&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;SAVE &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; QUIT
----------------------------------------------------------------------------
*****************************************************************************
按 active-----save &nbsp;
显示：
Activeelaying eth0 initialization
Save:Siocdelrt:no such process
&nbsp; &nbsp; siocaddrt:no such device
为啥不能保存，显示没有进程，没有设备阿！！！
:em19: &nbsp; &nbsp; :em27: